esphome · jesserockz · Apr 24, 2026 · Jan 2, 2026 · Jan 2, 2026 · Jan 2, 2026
diff --git a/src/docs/devices/AVATTO-S06-IR-Remote-no-temp-no-humidity/index.md b/src/docs/devices/AVATTO-S06-IR-Remote-no-temp-no-humidity/index.md
@@ -61,7 +61,7 @@ between the GPIO13 and the RESET pin of the ESP8266 MCU.
 ```yaml
 # Basic Config
 ---
-# https://esphome.io/devices/esp8266.html
+# https://esphome.io/components/esp8266/
 esphome:
   name: ir_remote
 
@@ -87,25 +87,25 @@ api:
 ota:
   password: !secret ota_password
 
-# https://esphome.io/components/status_led.html
+# https://esphome.io/components/status_led/
 status_led:
   pin: 4
 
-# https://esphome.io/components/remote_receiver.html
+# https://esphome.io/components/remote_receiver/
 remote_receiver:
   id: rcvr
   pin:
     number: 5
     mode: INPUT_PULLUP
     inverted: True
 
-# https://www.esphome.io/components/remote_transmitter.html
+# https://www.esphome.io/components/remote_transmitter/
 remote_transmitter:
   id: tamtr
   pin: 14
   carrier_duty_percent: 50%
 
-# https://esphome.io/components/climate/ir_climate.html
+# https://esphome.io/components/climate/climate_ir/
 climate:
   - platform: toshiba
     id: ac
@@ -126,7 +126,7 @@ switch:
           fan_mode: AUTO
           swing_mode: VERTICAL
 
-    # https://esphome.io/components/switch/shutdown.html
+    # https://esphome.io/components/switch/shutdown/
   - platform: shutdown
     name: "IR Remote Shutdown"
     id: ir_remote_shutdown

diff --git a/src/docs/devices/AWP04L/index.md b/src/docs/devices/AWP04L/index.md
@@ -39,7 +39,7 @@ esphome:
 
 esp8266:
   board: esp01_1m
-  restore_from_flash: true #writes each state change to flash for switch or light with restore_mode: RESTORE_DEFAULT_OFF/ON, see https://esphome.io/components/esphome.html#esp8266-restore-from-flash
+  restore_from_flash: true #writes each state change to flash for switch or light with restore_mode: RESTORE_DEFAULT_OFF/ON, see https://esphome.io/components/esphome/#configuration-variables-3
 
 wifi:
   ssid: !secret wifi_ssid
@@ -134,7 +134,7 @@ sensor:
     change_mode_every: 1 #Skips first reading after each change, so this will double the update interval. Default 8
     update_interval: 10s #20 second effective update rate for Power, 40 second for Current and Voltage. Default 60s
 
-  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
+  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy/
   - platform: total_daily_energy
     name: ${friendly_name} Total Daily Energy
     power_id: wattage
@@ -238,7 +238,7 @@ light:
             if (state == 2)
               state = 0;
 
-# Blink the red light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led.html instead but then we couldn't use the red light for other things as well.
+# Blink the red light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led/ instead but then we couldn't use the red light for other things as well.
 interval:
   - interval: 500ms
     then:
@@ -276,7 +276,7 @@ esphome:
 
 esp8266:
   board: esp01_1m
-  restore_from_flash: true #writes each state change to flash for switch or light with restore_mode: RESTORE_DEFAULT_OFF/ON, see https://esphome.io/components/esphome.html#esp8266-restore-from-flash
+  restore_from_flash: true #writes each state change to flash for switch or light with restore_mode: RESTORE_DEFAULT_OFF/ON, see https://esphome.io/components/esphome/#configuration-variables-3
 
 wifi:
   ssid: !secret wifi_ssid
@@ -371,7 +371,7 @@ sensor:
     change_mode_every: 1 #Skips first reading after each change, so this will double the update interval. Default 8
     update_interval: 10s #20 second effective update rate for Power, 40 second for Current and Voltage. Default 60s
 
-  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
+  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy/
   - platform: total_daily_energy
     name: ${friendly_name} Total Daily Energy
     power_id: wattage
@@ -475,7 +475,7 @@ light:
             if (state == 2)
               state = 0;
 
-# Blink the red light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led.html instead but then we couldn't use the red light for other things as well.
+# Blink the red light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led/ instead but then we couldn't use the red light for other things as well.
 interval:
   - interval: 500ms
     then:

diff --git a/src/docs/devices/Aoycocr-X10S-Plug/index.md b/src/docs/devices/Aoycocr-X10S-Plug/index.md
@@ -44,7 +44,7 @@ esphome:
 
 esp8266:
   board: esp01_1m
-  restore_from_flash: true #writes each state change to flash for switch or light with restore_mode: RESTORE_DEFAULT_OFF/ON, see https://esphome.io/components/esphome.html#esp8266-restore-from-flash
+  restore_from_flash: true #writes each state change to flash for switch or light with restore_mode: RESTORE_DEFAULT_OFF/ON, see https://esphome.io/components/esphome/#configuration-variables-3
 
 wifi:
   ssid: !secret wifi_ssid
@@ -139,7 +139,7 @@ sensor:
     change_mode_every: 1 #Skips first reading after each change, so this will double the update interval. Default 8
     update_interval: 10s #20 second effective update rate for Power, 40 second for Current and Voltage. Default 60s
 
-  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
+  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy/
   - platform: total_daily_energy
     name: ${friendly_name} Total Daily Energy
     power_id: wattage
@@ -243,7 +243,7 @@ light:
             if (state == 2)
               state = 0;
 
-# Blink the red light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led.html instead but then we couldn't use the red light for other things as well.
+# Blink the red light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led/ instead but then we couldn't use the red light for other things as well.
 interval:
   - interval: 500ms
     then:
@@ -378,7 +378,7 @@ sensor:
     change_mode_every: 1 #Skips first reading after each change, so this will double the update interval. Default 8
     update_interval: 10s #20 second effective update rate for Power, 40 second for Current and Voltage. Default 60s
 
-  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
+  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy/
   - platform: total_daily_energy
     name: ${friendly_name} Total Daily Energy
     power_id: wattage
@@ -482,7 +482,7 @@ light:
             if (state == 2)
               state = 0;
 
-# Blink the red light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led.html instead but then we couldn't use the red light for other things as well.
+# Blink the red light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led/ instead but then we couldn't use the red light for other things as well.
 interval:
   - interval: 500ms
     then:

diff --git a/src/docs/devices/Arlec-Grid-Connect-Smart-87cm-Linkable-CCT-Bar-Light/index.md b/src/docs/devices/Arlec-Grid-Connect-Smart-87cm-Linkable-CCT-Bar-Light/index.md
@@ -9,7 +9,7 @@ difficulty: 5
 
 The `Arlec Grid Connect Smart 87cm Linkable CCT Bar Light` is part of the
 [Grid Connect ecosystem](https://grid-connect.com.au/) sold at Bunnings in Australia and uses the
-Tuya [CBLC9](https://developer.tuya.com/en/docs/iot/cblc9-module-datasheet) module.
+Tuya [CBLC9](https://developer.tuya.com/docs/iot/cblc9-module-datasheet?id=Ka42cqnj9r0i5) module.
 This module is a variant of the BK7231 family and must be re-flashed or replaced with an ESP8266
 series module which fits inside the housing.
 

diff --git a/src/docs/devices/Arlec-Grid-Connect-Smart-LED-Globe-CWWW/index.md b/src/docs/devices/Arlec-Grid-Connect-Smart-LED-Globe-CWWW/index.md
@@ -19,7 +19,7 @@ as it was impossible to directly specify `brightness` and `color_temp` values un
 
 At the time of writing, you can now use the direct integration `color_temperature` platform from ESPHome. By using this
 platform, it opens up the ability to also add
-[light effects](https://esphome.io/components/light/index.html#light-effects) to the bulb as well.
+[light effects](https://esphome.io/components/light/#light-effects) to the bulb as well.
 
 The `GLD112HA` uses a `BP5926 chip` to drive the LED's and this chip uses two PWM signals to set the colour temperature
 and brightness. The bulb comes in both B22 and E27 bayonet fitting.

diff --git a/src/docs/devices/Arlec-PC191HA-Plug/index.md b/src/docs/devices/Arlec-PC191HA-Plug/index.md
@@ -75,7 +75,8 @@ After that, you can use ESPHome's OTA functionality to make any further changes.
 The case is ultrasonic-welded shut. With a spudger, blade, or other thin-edged tool you can pry it open (there will be
 some cosmetic damage). There will also be some silicone holding everything together which can be overcome with some
 effort. The CB2S module is soldered in a thru-hole configuration on the top edge of the main board. Refer to the
-[CB2S datasheet](https://developer.tuya.com/en/docs/Document/cb2s-module-datasheet) for its pinout, you'll need a USB to
+[CB2S datasheet](https://developer.tuya.com/docs/iot/cb2s-module-datasheet?id=Kafgfsa2aaypq)
+for its pinout, you'll need a USB to
 TTL serial adapter and a soldering iron. It's best to remove the module from the main board, as the serial adapater's
 3.3V power supply probably isn't enough for the module to boot with peripherals attached. Flash with
 [ltchiptool](https://github.com/libretiny-eu/ltchiptool) or similar.
@@ -486,6 +487,5 @@ sensor:
 
 [pc191ha-forum]: https://www.elektroda.com/rtvforum/topic3944452.html
 [pc191ha-blakadder]: https://templates.blakadder.com/arlec_PC191HA.html
-[pc191ha-ha-energy]:
-https://community.home-assistant.io/t/energy-consumption-and-arlec-grid-connect-tuya-smart-plug/335508/55
-[pc191ha-ha-kickstart]: https://community.home-assistant.io/t/kickstart-bk7231t-to-esphome-add-on/701658
+[pc191ha-ha-energy]: https://community.home-assistant.io/t/335508/55
+[pc191ha-ha-kickstart]: https://community.home-assistant.io/t/701658
diff --git a/src/docs/devices/Awow-EU3S-Power-Monitoring-Plug/index.md b/src/docs/devices/Awow-EU3S-Power-Monitoring-Plug/index.md
@@ -115,7 +115,7 @@ sensor:
     current_resistor: ${current_res}
     voltage_divider: ${voltage_div}
 
-  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
+  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy/
   - platform: total_daily_energy
     name: ${friendly_name} Total Daily Energy
     icon: mdi:circle-slice-3
@@ -182,7 +182,7 @@ light:
   output: ${devicename}_blue_output
   id: ${devicename}_blue_led
 
-# Blink the blue light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led.html instead but then we couldn't use the blue light for other things as well.
+# Blink the blue light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led/ instead but then we couldn't use the blue light for other things as well.
 # Only if not connected after 30s
 interval:
   - interval: 2000ms

diff --git a/src/docs/devices/BlitzWolf-BW-SHP2-Power-Monitoring-Plug/index.md b/src/docs/devices/BlitzWolf-BW-SHP2-Power-Monitoring-Plug/index.md
@@ -124,7 +124,7 @@ sensor:
     current_resistor: ${current_res}
     voltage_divider: ${voltage_div}
 
-  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
+  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy/
   - platform: total_daily_energy
     name: ${friendly_name} Total Daily Energy
     icon: mdi:circle-slice-3
@@ -196,7 +196,7 @@ light:
   output: ${devicename}_blue_output
   id: ${devicename}_blue_led
 
-# Blink the blue light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led.html instead but then we couldn't use the blue light for other things as well.
+# Blink the blue light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led/ instead but then we couldn't use the blue light for other things as well.
 # Only if not connected after 30s
 interval:
   - interval: 2000ms
@@ -308,7 +308,7 @@ sensor:
     current_resistor: ${current_res}
     voltage_divider: ${voltage_div}
 
-  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
+  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy/
   - platform: total_daily_energy
     name: ${friendly_name} Total Daily Energy
     icon: mdi:circle-slice-3
@@ -380,7 +380,7 @@ light:
   output: ${devicename}_blue_output
   id: ${devicename}_blue_led
 
-# Blink the blue light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led.html instead but then we couldn't use the blue light for other things as well.
+# Blink the blue light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led/ instead but then we couldn't use the blue light for other things as well.
 # Only if not connected after 30s
 interval:
   - interval: 2000ms

diff --git a/src/docs/devices/BlitzWolf-BW-SHP3/index.md b/src/docs/devices/BlitzWolf-BW-SHP3/index.md
@@ -81,7 +81,7 @@ sensor:
     current_resistor: ${current_res}
     voltage_divider: ${voltage_div}
 
-  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
+  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy/
   - platform: total_daily_energy
     name: ${propername} Total Daily Energy
     icon: mdi:circle-slice-3

diff --git a/src/docs/devices/Brilliant-Lighting-BL20925-Power-Monitoring-Plug/index.md b/src/docs/devices/Brilliant-Lighting-BL20925-Power-Monitoring-Plug/index.md
@@ -95,7 +95,7 @@ sensor:
       name: ${friendly_name} Voltage
       unit_of_measurement: V
 
-  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
+  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy/
   - platform: total_daily_energy
     name: ${friendly_name} Total Daily Energy
     power_id: wattage
@@ -159,7 +159,7 @@ light:
   output: brilliant_smartplug_1_blue_output
   id: brilliant_smartplug_1_blue_led
 
-# Blink the blue light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led.html instead but then we couldn't use the blue light for other things as well.
+# Blink the blue light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led/ instead but then we couldn't use the blue light for other things as well.
 # Only if not connected after 30s
 interval:
   - interval: 2000ms

diff --git a/src/docs/devices/Brilliant-Smart-WiFi-Wall-Mounted-Light-Switch/index.md b/src/docs/devices/Brilliant-Smart-WiFi-Wall-Mounted-Light-Switch/index.md
@@ -28,8 +28,8 @@ This YAML is cobbled together from:
 - [ESPHome Tuya switch documentation][brilliant-tuya-switch]
 
 [brilliant-deta]: https://devices.esphome.io/devices/DETA-Grid-Connect-Smart-Switch/
-[brilliant-tuya]: https://esphome.io/components/tuya.html
-[brilliant-tuya-switch]: https://esphome.io/components/switch/tuya.html
+[brilliant-tuya]: https://esphome.io/components/tuya/
+[brilliant-tuya-switch]: https://esphome.io/components/switch/tuya/
 
 ```yaml
 substitutions:

diff --git a/src/docs/devices/CloudFree-EU-Plug-P1EU/index.md b/src/docs/devices/CloudFree-EU-Plug-P1EU/index.md
@@ -120,7 +120,7 @@ sensor:
     current_resistor: ${current_res}
     voltage_divider: ${voltage_div}
 
-  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy.html
+  # Reports the total Power so-far each day, resets at midnight, see https://esphome.io/components/sensor/total_daily_energy/
   - platform: total_daily_energy
     name: ${friendly_name} Total Daily Energy
     icon: mdi:circle-slice-3
@@ -187,7 +187,7 @@ light:
   output: ${devicename}_blue_output
   id: ${devicename}_blue_led
 
-# Blink the blue light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led.html instead but then we couldn't use the blue light for other things as well.
+# Blink the blue light if we aren't connected to WiFi. Could use https://esphome.io/components/status_led/ instead but then we couldn't use the blue light for other things as well.
 # Only if not connected after 30s
 interval:
   - interval: 2000ms

diff --git a/src/docs/devices/Connected-Consumer-Fuel-Smart-Oil-Gauge/index.md b/src/docs/devices/Connected-Consumer-Fuel-Smart-Oil-Gauge/index.md
@@ -44,7 +44,7 @@ SKU: CCF-901
    ![alt text](Flashing-Edge.jpg "Edge Flashing Connection")
 5. Follow the directions as outlined by ESPHome for physically connecting to your device:
 
-[https://esphome.io/guides/physical_device_connection#physically-connecting-to-your-device](https://esphome.io/guides/physical_device_connection#physically-connecting-to-your-device)
+[https://esphome.io/guides/physical_device_connection#physically-connecting-to-your-device](https://esphome.io/guides/physical_device_connection/)
 
 ## Operation
 
@@ -86,7 +86,7 @@ like an HC-SR04 ultrasonic distance sensor.
 ### TPL5111 - Nano-Power System Timer for Power Gating
 
 SMD Marking: ZFVX \
-[https://www.ti.com/lit/ds/symlink/tpl5111.pdf?ts=1739630376626&ref_url=https%253A%252F%252Fwww.google.com%252F](https://www.ti.com/lit/ds/symlink/tpl5111.pdf?ts=1739630376626&ref_url=https%253A%252F%252Fwww.google.com%252F)
+[https://www.ti.com/lit/ds/symlink/tpl5111.pdf?ts=1739630376626&ref_url=https%253A%252F%252Fwww.google.com%252F](https://www.ti.com/lit/ds/symlink/tpl5111.pdf)
 
 Power Gating of 3.3VDC to the ESP8266.\
 Hardwired to restart the controller every hour.\
@@ -96,7 +96,7 @@ Timer will cut 3.3V when DONE pin goes HIGH, will wake after 1hr.
 
 SMD Marking: C5F \
 Datasheet:
-[https://www.ti.com/lit/ds/symlink/sn74lvc1g3157.pdf?ts=1740393486499](https://www.ti.com/lit/ds/symlink/sn74lvc1g3157.pdf?ts=1740393486499)
+[https://www.ti.com/lit/ds/symlink/sn74lvc1g3157.pdf?ts=1740393486499](https://www.ti.com/lit/ds/symlink/sn74lvc1g3157.pdf)
 
 Switches the connection to A0 (GPIO17)
 

diff --git a/src/docs/devices/DETA-Grid-Connect-Single-Gang-Two-Way-6951HA/index.md b/src/docs/devices/DETA-Grid-Connect-Single-Gang-Two-Way-6951HA/index.md
@@ -55,9 +55,6 @@ adding a 10k pull-down resistor on GPIO15.
 
 ### Series 1 (WB3S) GPIO Pinouts
 
-_See
-[Pinouts on WB3S Module Datasheet](https://developer.tuya.com/en/docs/iot/wb3s-module-datasheet?id=K9dx20n6hz5n4#title-5-Interface%20pin%20definition) for more detail_
-
 | Pin | Function                                                                                                                                    |
 | --- | ------------------------------------------------------------------------------------------------------------------------------------------- |
 | P24 | Status LED _(inverted)_                                                                                                                     |

diff --git a/src/docs/devices/DETA-Grid-Connect-Two-Gang-Two-Way-6952HA/index.md b/src/docs/devices/DETA-Grid-Connect-Two-Gang-Two-Way-6952HA/index.md
@@ -51,7 +51,7 @@ configuration below.
 ### Series 2 (CB3S) GPIO Pinouts
 
 _See
-[Pinouts on CB3S Module Datasheet](https://developer.tuya.com/en/docs/iot/cb3s?id=Kai94mec0s076#title-5-Pin%20definition) for more detail_
+[Pinouts on CB3S Module Datasheet](https://developer.tuya.com/docs/iot/cb3s?id=Kai94mec0s076#title-5-Pin%20definition) for more detail_
 
 | Pin | Function                                                                                                                                      |
 | --- | --------------------------------------------------------------------------------------------------------------------------------------------- |

diff --git a/...s/Deta-Grid-Connect-Smart-Fan-Speed-Controller-with-Touch-Light-Switch/index.md b/...s/Deta-Grid-Connect-Smart-Fan-Speed-Controller-with-Touch-Light-Switch/index.md
@@ -18,12 +18,11 @@ Original version uses ESP8266 controller.
 
 ### Series 2
 
-Newer revision uses BK7231T controller on the Tuya
-[WB3S module](https://developer.tuya.com/en/docs/iot/wb3s-module-datasheet?id=K9dx20n6hz5n4).
+Newer revision uses BK7231T controller on the Tuya WB3S module.
 
 ### Series 3
 
-revision uses BK7231N controller on the Tuya [CB3S module](https://developer.tuya.com/en/docs/iot/cb3s?id=Kai94mec0s076)
+revision uses BK7231N controller on the Tuya [CB3S module](https://developer.tuya.com/docs/iot/cb3s?id=Kai94mec0s076)
 
 ## GPIO Pinout