diff --git a/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter-Old/index.md b/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter-Old/index.md
new file mode 100644
index 000000000..bba29be71
--- /dev/null
+++ b/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter-Old/index.md
@@ -0,0 +1,218 @@
+---
+title: Kogan SmarterHome Smart Power Board With USB Ports & Energy Meter
+Model: KASPS10A3P3UA
+date-published: 2020-05-25
+type: plug
+standard: au
+board: esp8266
+---
+  ![alt text](kogan-smarterhome-smart-power-board-with-usb-ports-energy-meter.jpg "Product Image")
+
+[Kogan SmarterHome™ Smart Power Board With USB Ports & Energy Meter - (KASPS10A3P3UA) - Manual](https://help.kogan.com/s/article/KoganSmarterHomeSmartPowerBoardWithUSBPortsEnergyMeterKASPS10A3P3UAManual)
+
+## GPIO Pinout
+
+| Pin    | Function                   |
+|--------|----------------------------|
+| GPIO00 | Push Button                |
+| GPIO01 | Green LED (Inverted: true) |
+| GPIO13 | Relay 1                    |
+| GPIO14 | Relay 2                    |
+| GPIO03 | Relay 3                    |
+| GPIO15 | Relay USB                  |
+| GPIO12 | HLW8012 SEL Pin            |
+| GPIO04 | HLW8012 CF Pin             |
+| GPIO05 | HLW8012 CF1 Pin            |
+
+**Note:** In the below configuration, the push button (and surrounding LED) is configured to only control Relay 3 (End Plug)
+
+## Basic Config
+
+```yaml
+substitutions:
+  device_name: kogan_strip_1
+  device_ip: 192.168.x.x
+  plug_icon: mdi:power-socket-au
+  usb_icon: mdi:usb-port
+  plug1_restore: ALWAYS_ON
+  plug2_restore: ALWAYS_OFF
+  plug3_restore: ALWAYS_OFF
+  usb_restore: ALWAYS_ON
+  
+  # Higher value gives lower watt readout
+  current_res: "0.00250"
+  # Lower value gives lower voltage readout
+  voltage_div: "799"
+
+esphome:
+  name: ${device_name}
+
+esp8266:
+  board: esp8285
+
+wifi:
+  ssid: !secret wifi_ssid
+  password: !secret wifi_password
+
+logger:
+
+api:
+  reboot_timeout: 15min
+  encryption:
+    key: !secret encryption_key
+
+ota:
+  password: !secret ota_password
+
+binary_sensor:
+  - platform: gpio
+    pin:
+      number: GPIO0
+      mode: INPUT_PULLUP
+      inverted: true
+    name: "${device_name}_button"
+    on_multi_click:
+      - timing:
+          - ON for 5ms to 350ms
+          - OFF for at least 750ms
+        then:
+          - switch.toggle: relayusb
+      - timing:
+          - ON for 5ms to 350ms
+          - OFF for 5ms to 350ms
+          - ON for 5ms to 350ms
+          - OFF for at least 750ms
+        then:
+          - switch.toggle: relay1
+      - timing:
+          - ON for 5ms to 350ms
+          - OFF for 5ms to 350ms
+          - ON for 5ms to 350ms
+          - OFF for 5ms to 350ms
+          - ON for 5ms to 350ms
+          - OFF for at least 750ms
+        then:
+          - switch.toggle: relay2
+      - timing:
+          - ON for 5ms to 350ms
+          - OFF for 5ms to 350ms
+          - ON for 5ms to 350ms
+          - OFF for 5ms to 350ms
+          - ON for 5ms to 350ms
+          - OFF for 5ms to 350ms
+          - ON for 5ms to 350ms
+          - OFF for at least 750ms
+        then:
+          - switch.toggle: relay3
+
+  - platform: status
+    name: "${device_name}_status"
+
+light:
+  - platform: status_led
+    id: green_led
+    pin:
+      number: GPIO1
+      inverted: true
+
+switch:
+  - platform: gpio
+    name: "${device_name}_plug1"
+    pin: GPIO13
+    id: relay1
+    icon: ${plug_icon}
+    restore_mode: ${plug1_restore}
+
+  - platform: gpio
+    name: "${device_name}_plug2"
+    pin: GPIO14
+    id: relay2
+    icon: ${plug_icon}
+    restore_mode: ${plug2_restore}
+
+  - platform: gpio
+    name: "${device_name}_plug3"
+    pin: GPIO3
+    id: relay3
+    icon: ${plug_icon}
+    restore_mode: ${plug3_restore}
+    on_turn_on:
+      - light.turn_on: green_led
+    on_turn_off:
+      - light.turn_off: green_led
+
+  - platform: gpio
+    name: "${device_name}_usb"
+    pin: GPIO15
+    id: relayusb
+    icon: ${usb_icon}
+    restore_mode: ${usb_restore}
+
+sensor:
+  - platform: hlw8012
+    sel_pin:
+      number: GPIO12
+      inverted: true
+    cf_pin: GPIO04
+    cf1_pin: GPIO05
+    current:
+      name: "${device_name}_current"
+      unit_of_measurement: A
+    voltage:
+      name: "${device_name}_voltage"
+      unit_of_measurement: V
+    power:
+      id: ${device_name}_wattage
+      name: "${device_name}_wattage"
+      unit_of_measurement: W
+    current_resistor: ${current_res}
+    voltage_divider: ${voltage_div}
+    change_mode_every: 8
+    update_interval: 15s
+
+  - platform: total_daily_energy
+    name: "${device_name}_daily_energy"
+    power_id: ${device_name}_wattage
+    filters:
+      - multiply: 0.001
+    unit_of_measurement: kWh
+
+  - platform: wifi_signal
+    name: "${device_name}_rssi"
+    update_interval: 5min
+
+  - platform: uptime
+    id: uptime_sec
+    name: "${device_name}_uptime"
+    update_interval: 5min
+
+text_sensor:
+  - platform: template
+    name: "${device_name}_upformat"
+    lambda: |-
+      uint32_t dur = id(uptime_sec).state;
+      int dys = 0;
+      int hrs = 0;
+      int mnts = 0;
+      if (dur > 86399) {
+        dys = trunc(dur / 86400);
+        dur = dur - (dys * 86400);
+      }
+      if (dur > 3599) {
+        hrs = trunc(dur / 3600);
+        dur = dur - (hrs * 3600);
+      }
+      if (dur > 59) {
+        mnts = trunc(dur / 60);
+        dur = dur - (mnts * 60);
+      }
+      char buffer[17];
+      sprintf(buffer, "%ud %02uh %02um %02us", dys, hrs, mnts, dur);
+      return {buffer};
+    icon: mdi:clock-start
+    update_interval: 5min
+
+time:
+  - platform: homeassistant
+    id: homeassistant_time
+```
diff --git a/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter-Old/kogan-smarterhome-smart-power-board-with-usb-ports-energy-meter.jpg b/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter-Old/kogan-smarterhome-smart-power-board-with-usb-ports-energy-meter.jpg
new file mode 100644
index 000000000..d4cfe4f1c
Binary files /dev/null and b/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter-Old/kogan-smarterhome-smart-power-board-with-usb-ports-energy-meter.jpg differ
diff --git a/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter/index.md b/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter/index.md
index ed094f04d..6cbfa9feb 100644
--- a/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter/index.md
+++ b/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter/index.md
@@ -1,225 +1,121 @@
 ---
 title: Kogan SmarterHome Smart Power Board With USB Ports & Energy Meter
-Model: KASPS10A3P3UA
-date-published: 2020-05-25
+Model: KASPS30WACB
+date-published: 2026-03-31
 type: plug
 standard: au
-board: esp8266
+board: bk72xx
 ---
   ![alt text](kogan-smarterhome-smart-power-board-with-usb-ports-energy-meter.jpg "Product Image")
 
-[Kogan SmarterHome™ Smart Power Board With USB Ports & Energy Meter - (KASPS10A3P3UA) - Manual](https://help.kogan.com/s/article/KoganSmarterHomeSmartPowerBoardWithUSBPortsEnergyMeterKASPS10A3P3UAManual)
+[Kogan SmarterHome™ Smart Power Board With USB Ports & Energy Meter - (KASPS30WACB) - Manual](https://help.kogan.com/s/article/Kogan-SmarterHome-30W-PD-Smart-Power-Board-with-Energy-Metre-3-Outlets-2-USB-C-Ports---KASPS30WACB---Manuals-and-Support)
 
-## GPIO Pinout
+## Programming Notes
 
-| Pin    | Function                   |
-|--------|----------------------------|
-| GPIO00 | Push Button                |
-| GPIO01 | Green LED (Inverted: true) |
-| GPIO13 | Relay 1                    |
-| GPIO14 | Relay 2                    |
-| GPIO03 | Relay 3                    |
-| GPIO15 | Relay USB                  |
-| GPIO12 | HLW8012 SEL Pin            |
-| GPIO04 | HLW8012 CF Pin             |
-| GPIO05 | HLW8012 CF1 Pin            |
+**Warning** This board is mains powered. Do not do ANYTHING while the board is powered. 
+Power the board via the 3.3v and GND pin and do not connect the board to the mains until you are fully disconnected and the board is fully reassembled.
 
-**Note:** In the below configuration, the push button (and surrounding LED) is configured to only control Relay 3 (End Plug)
+To program the board you will need to disassemble the powerboard and solder jumper cables to the CEN, TX, RX, 3.3v and GND pins.
+You will also need to bridge the CSN pin on the back of the module to GND (e.g back of the chip) to put the board into programming mode.
 
-## Basic Config
+![pins go where](kogan-pins-where.png "Pins go where")
 
-```yaml
-substitutions:
-  device_name: kogan_strip_1
-  device_ip: 192.168.x.x
-  plug_icon: mdi:power-socket-au
-  usb_icon: mdi:usb-port
-  plug1_restore: ALWAYS_ON
-  plug2_restore: ALWAYS_OFF
-  plug3_restore: ALWAYS_OFF
-  usb_restore: ALWAYS_ON
-  
-  # Higher value gives lower watt readout
-  current_res: "0.00250"
-  # Lower value gives lower voltage readout
-  voltage_div: "799"
+Attach 3.3v, GND, TX and RX to your serial adapter and tap CEN to GND while attempting to flash the board in ltchiptool.
+It may take a couple attempts to get the timing right, but you should see the board flash and then disconnect the CSN-GND bridge after flashing is complete.
 
-esphome:
-  name: ${device_name}
+## GPIO Pinout
+
+| Pin       | Function                     |
+|-----------|------------------------------|
+| P9 (TX1)  | BL0942 UART TX               |
+| P10 (RX1) | BL0942 UART RX               |
+| P6 (PWM0) | Port 1 relay                 |
+| P7 (PWM1) | Port 2 relay                 |
+| P26(PWM2) | Port 3 relay                 |
+| P24(PWM4) | Push button                  |
+| P8 (PWM5) | Status LED (inverted)        |
+
+**Note:** The button and LED are not configured to do anything in this configuration, but they are included for completeness.
 
-esp8266:
-  board: esp8285
+## Basic Config
 
+```yaml
 wifi:
   ssid: !secret wifi_ssid
   password: !secret wifi_password
-  manual_ip:
-    static_ip: ${device_ip}
-    gateway: 192.168.x.x
-    subnet: 255.255.255.0
 
+# Enable logging
 logger:
 
-web_server:
-  port: 80
-  
+# Enable Home Assistant API
 api:
-  reboot_timeout: 15min
-  encryption:
-    key: !secret encryption_key
 
 ota:
-  password: !secret ota_password
+
+esphome:
+  name: powerboard
+  platformio_options:
+    build_flags:
+      - -DLWIP_DHCP_DOES_ACD_CHECK=0
+
+bk72xx:
+  board: cb2s
+  framework:
+    version: latest
+    debug:
+      - WIFI
+
+
+uart:
+  tx_pin: "TX1"
+  rx_pin:
+    number: "RX1"
+    mode:
+      pullup: true
+      input: true
+  baud_rate: 4800
 
 binary_sensor:
   - platform: gpio
     pin:
-      number: GPIO0
-      mode: INPUT_PULLUP
-      inverted: true
-    name: "${device_name}_button"
-    on_multi_click:
-      - timing:
-          - ON for 5ms to 350ms
-          - OFF for at least 750ms
-        then:
-          - switch.toggle: relayusb
-      - timing:
-          - ON for 5ms to 350ms
-          - OFF for 5ms to 350ms
-          - ON for 5ms to 350ms
-          - OFF for at least 750ms
-        then:
-          - switch.toggle: relay1
-      - timing:
-          - ON for 5ms to 350ms
-          - OFF for 5ms to 350ms
-          - ON for 5ms to 350ms
-          - OFF for 5ms to 350ms
-          - ON for 5ms to 350ms
-          - OFF for at least 750ms
-        then:
-          - switch.toggle: relay2
-      - timing:
-          - ON for 5ms to 350ms
-          - OFF for 5ms to 350ms
-          - ON for 5ms to 350ms
-          - OFF for 5ms to 350ms
-          - ON for 5ms to 350ms
-          - OFF for 5ms to 350ms
-          - ON for 5ms to 350ms
-          - OFF for at least 750ms
-        then:
-          - switch.toggle: relay3
-
-  - platform: status
-    name: "${device_name}_status"
-
-light:
-  - platform: status_led
-    id: green_led
-    pin:
-      number: GPIO1
+      number: "PWM4"
+      mode:
+        input: true
+        pullup: true
       inverted: true
+    name: "Button"
+
+sensor:
+  - platform: bl0942
+    voltage:
+      name: "BL0942 Voltage"
+    current:
+      name: "BL0942 Current"
+    power:
+      name: "BL0942 Power"
+      filters:
+        - multiply: -1
+    energy:
+      name: "BL0942 Energy"
+    frequency:
+      name: "BL0942 Frequency"
 
 switch:
   - platform: gpio
-    name: "${device_name}_plug1"
-    pin: GPIO13
-    id: relay1
-    icon: ${plug_icon}
-    restore_mode: ${plug1_restore}
-
+    name: "Port 1"
+    pin: "PWM0"
+    restore_mode: RESTORE_DEFAULT_ON
   - platform: gpio
-    name: "${device_name}_plug2"
-    pin: GPIO14
-    id: relay2
-    icon: ${plug_icon}
-    restore_mode: ${plug2_restore}
-
+    name: "Port 2"
+    pin: "PWM1"
+    restore_mode: RESTORE_DEFAULT_ON
   - platform: gpio
-    name: "${device_name}_plug3"
-    pin: GPIO3
-    id: relay3
-    icon: ${plug_icon}
-    restore_mode: ${plug3_restore}
-    on_turn_on:
-      - light.turn_on: green_led
-    on_turn_off:
-      - light.turn_off: green_led
-
+    name: "Port 3"
+    pin: "PWM2"
+    restore_mode: RESTORE_DEFAULT_ON
   - platform: gpio
-    name: "${device_name}_usb"
-    pin: GPIO15
-    id: relayusb
-    icon: ${usb_icon}
-    restore_mode: ${usb_restore}
-
-sensor:
-  - platform: hlw8012
-    sel_pin:
-      number: GPIO12
-      inverted: true
-    cf_pin: GPIO04
-    cf1_pin: GPIO05
-    current:
-      name: "${device_name}_current"
-      unit_of_measurement: A
-    voltage:
-      name: "${device_name}_voltage"
-      unit_of_measurement: V
-    power:
-      id: ${device_name}_wattage
-      name: "${device_name}_wattage"
-      unit_of_measurement: W
-    current_resistor: ${current_res}
-    voltage_divider: ${voltage_div}
-    change_mode_every: 8
-    update_interval: 15s
-
-  - platform: total_daily_energy
-    name: "${device_name}_daily_energy"
-    power_id: ${device_name}_wattage
-    filters:
-      - multiply: 0.001
-    unit_of_measurement: kWh
-
-  - platform: wifi_signal
-    name: "${device_name}_rssi"
-    update_interval: 5min
-
-  - platform: uptime
-    id: uptime_sec
-    name: "${device_name}_uptime"
-    update_interval: 5min
-
-text_sensor:
-  - platform: template
-    name: "${device_name}_upformat"
-    lambda: |-
-      uint32_t dur = id(uptime_sec).state;
-      int dys = 0;
-      int hrs = 0;
-      int mnts = 0;
-      if (dur > 86399) {
-        dys = trunc(dur / 86400);
-        dur = dur - (dys * 86400);
-      }
-      if (dur > 3599) {
-        hrs = trunc(dur / 3600);
-        dur = dur - (hrs * 3600);
-      }
-      if (dur > 59) {
-        mnts = trunc(dur / 60);
-        dur = dur - (mnts * 60);
-      }
-      char buffer[17];
-      sprintf(buffer, "%ud %02uh %02um %02us", dys, hrs, mnts, dur);
-      return {buffer};
-    icon: mdi:clock-start
-    update_interval: 5min
-
-time:
-  - platform: homeassistant
-    id: homeassistant_time
+    name: "LED"
+    pin: "PWM5"
+    restore_mode: RESTORE_DEFAULT_ON
+    inverted: true
 ```
diff --git a/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter/kogan-pins-where.png b/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter/kogan-pins-where.png
new file mode 100644
index 000000000..2e3cc145b
Binary files /dev/null and b/src/docs/devices/Kogan-Smarterhome-Smart-Power-Board-With-Usb-Ports-Energy-Meter/kogan-pins-where.png differ